May 26, 2018

I blasted them with compressed air, reassembled and so far so good. When I put the hard drive back in, the computer would not boot up. CJ, I took your solution and went to my local computer store and picked up Ceramique an Arctic Silver product. When you turn on the laptop, does the fan start spinning? Table of Contents Add to my manuals Add. If that does not work, is there a tutorial on how to apply artic gel, or to remove the fan to celean out more?

Uploader: Zuluramar
Date Added: 23 January 2015
File Size: 45.25 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 25583
Price: Free* [*Free Regsitration Required]

I looked under all the tabs in the power management. Page 84 Removal and Replacement Procedures 5. What can be the reason of such problems? Stay connected to the new QuickSpecs QuickSpecs is evolving and improving, stay on top of the latest development by subscribing to QuickSpecs News. Any any ideas on the display problem would be much appreciated also. Keyboard Removal and Replacement Procedures 5. Start to assemble the laptop and test after each step.

hp compaq nc6000 base system device

Магазин за електроника Пулсатор София

Remove the modem board. I think that cleaning the heatsink will not help. Removal ddvice Replacement Procedures 7. The booting up problem existed before Edvice cleaned out the heatsink. When I remove the power adapter cable from the back of the laptop, the laptop still thinks that it is running on AC power. I assembled everything and switched the laptop on, but the temperature is about the same as before.

Removing the Fan from the Fan Assembly Reverse the above procedure to hp compaq nc6000 base system device the fan assembly.

Removing the Battery Bezel Reverse the above procedure to install the battery pack and battery bezel. Slide and hold the MultiBay release latch to the right 1. Was going to pay pounds to get it fixed: Not realizing that the a75 had comppaq be taken apart to access the heat sink, I took the hard drive out in the process of blowing hp compaq nc6000 base system device air into the computer to clear it.

Toshiba suddenly shuts down by itself

You should be able to see the CPU speed. You copmaq to remove the heatsink only if you want to replace thermal grease on the CPU. Can u advcie how much it will cost hp compaq nc6000 base system device replace the screen rgds amit. Thank you though for your reply I hope this will help other Toshiba users in the future! Remove the LED switch cover Section 5.

ckmpaq As you see, a damaged power cord can a damaged power jack can have the same symptoms. I would try to upgrade BIOS and hp compaq nc6000 base system device the keyboard and the touchpad connectors on the system board. Bootable Install bootable Nonsystem diskette diskette and disk message?


Randy, It looks like you know how to take it apart with closed eyes. The DC jack is kinda flimsy, looking at it from the outside. Fan Assembly Removal and Replacement Procedures 5.

QuickSpecs access through HP Marketing Document Library

What else should I be looking for? Lift the right side of the cover up and swing it to the left 2. I had to do debice several times before having a normal starting maybe timesjust take the time to find the right position.

Now I wanna get the permanent solution for my laptop so Hp compaq nc6000 base system device can use smoothly, what can I do? It was total black. Remove the hard drive by following these steps: If necessary, disconnect the modem cable from the system board and remove the cable.

It looks like that the battery charges when the laptop is turned off. Remove the battery pack. Remove the fan assembly 3 from the notebook. I just purchased an Advent laptop. I tried reseting, turning the laptop off, taking the battery hp compaq nc6000 base system device and so on and I got the same response. Reseat monitor cable connector at Port Replicator. I forgot to mark those screws on the picture in Step2.

Hi, I have syztem toshiba satellite AS which according to the gig sqpuads the memory that come with this computer MB is bad. When I try to use the recovery CD I get the following message:. Hey, very nice job for doing this Page for all of us that need some manuals to fix the overheating problems, My father bought an A75 and after 1 year and a half working great hp compaq nc6000 base system device started to have some problems, so he took it to a repair center and it work great just for 3 weeks, so I devcie this page and I followed the instructions and applied some Arctic Silver 5 and hp compaq nc6000 base system device working great for now, hope it stays like this.

Sometimes the laptop will stay on for hours and sometimes it shuts off after a few minutes. I applied Arctic Silver thermal conductor between them and I feel sevice probably did the trick. This morning tried again with the same result.