Graphic and Video Cards


May 24, 2018

Color Ribbon Ymckt View larger image. Push the sensor out of the duplex chassis. Do not insert a cleaning card! MS Mag Stripe Error Control information passed through by the printer driver was not accepted by the magnetic stripe module. The printer must be connected to a computer locally or through a network to print cards.

Uploader: Gugami
Date Added: 7 June 2017
File Size: 20.46 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 81386
Price: Free* [*Free Regsitration Required]

Page Verify the settings with a new ribbon and also with a near-empty ribbon, as the spool diameters datacard cp60 impact the results. After the value has been changed, press the Enter key to apply the settings and reboot the printer.

Release the belt tension, and remove the transport belt. We offer the broadest range of desktop printers, from high-speed systems that apply customized security laminates and personalize smart cards completely in datacard cp60 to low-cost, low-volume models for basic needs.

Page 16 Open Card 17 file2prn utility 23 firmware revision 48 flash error 73 full-color identifying printer feature 4 print cycles 49 support by data format 20 gateway address setting 57 viewing 51 handling cards Remove the Ribbon Guide p.

Page Carefully push down on the sensor datacard cp60 above and remove it through the datacard cp60 of the chassis, being careful not to lose the spacer.

Page 62 Datacard cp60 Motors The best way to determine if a motor has failed versus a main control board failure, is to swap the motor with a similar motor. The diagram datacard cp60 the typical locations for the magnetic stripe and smart card chip. No Preference filter applied.

Datacard Printer Ribbons & Supplies | ID Zone

This datacwrd lead to slightly more data datacard cp60 errors. Best Match Best Match. Up to 4 logos can be stored in the printer. Print Datacard cp60 information Select this option and click Query to display the type of ribbon detected by the printer in the display window Laminate information This option is not available for the CP60 and CP60 Plus printers.

Click Reset Printer as datcaard is a good practice to reset the printer before returning to card production. The printer moves the rollers when it datacard cp60 to pick the card. If it is, power the print off and on; the printer might detect the module when the printer powers up.

The input hopper datacard cp60 empty. Comments to this Manuals Your Name.

Page 75 A card was not picked successfully. Contact Smart Cards A contact smart card needs to connect to datacard cp60 external interface to provide the datacard cp60 with power and set up serial communication.


Datacard CP60 Plus ID Card Printer

If a motor has failed, then datacard cp60 replacement motor should function. Page 99 If this position cannot be determined, set the offset so the trailing edge of the card covers the location of the magnetic head but does datacard cp60 cover the location of the magnetic head’s pivot pin. Page 57 Reassemble the printer.

The duplex entry sensor xp60 not blocked when expected. You may want to search: Printhead Fan Printhead Fan There are two different sizes of fans in the printers. Also See for CP60 Service manual – pages. Be sure to select the correct update file if you are using Printer Diagnostics or the file2prn utility. Unfollow datacard cp60 to stop datacard cp60 updates on your eBay Feed. Squeeze the ends of the spring clutch and pull it off the boss.

Page To change the value, press the Up or Down arrow to increment or decrement the datacard cp60 value in each adtacard. If the problem persists, see Info Central for detailed information about solving card appearance problems. Troubleshooting This chapter provides datacarx for troubleshooting problems with the Datacard cp60 and CP60 Plus card printers. The gray test card is used to detect strobe misadjustment.

Tilt the LCD inward over the top of the retaining tab. You will then be asked to which program group the icon should be added. Page 61 If the replacement sensor is non-functional and other sensors in the printer are observed to be functional, then the main control board is defective. Zhuhai Winrun Technology Co. Page PC 65 responding to 65 where displayed 19 printer 36 SNMP support 36 monochrome identifying printer 4 print cycles 49 print ribbons 63 printing intensity datacard cp60 support by data format 20 MS datacarr 82 network change printer settings 53 Page As soon as possible, grasp the datacard cp60 spring and remove dataczrd datacard cp60 it gets loose.

Card in position The sensor that detects a card is located on the smart card connector. Safety Use proper lifting techniques when moving or installing the equipment.