Distribution board schedule

Edison base for branch circuits and one or more fuse blocks containing cartridge fuses for purposes such as major appliance circuits. The dimmers are equally divided across the three incoming phases. The incoming bare, stranded ground wire can be seen near the bottom of the neutral bus bar. In Canadian service entrance panelboards the main switch or circuit breaker is located in a service box , a section of the enclosure separated from the rest of the panelboard, so that when the main switch or breaker is switched off no live parts are exposed when servicing the branch circuits. The other problem with recessing a distribution board into a wall is that if the wall is solid, a lot of brick or block might need to be removed—generally for this reason, recessed boards would only be installed on new-build projects when the required space can be built into the wall.

Uploader: Megrel
Date Added: 27 May 2014
File Size: 38.54 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 93608
Price: Free* [*Free Regsitration Required]





North American distribution boards are typically housed in sheet metal enclosures, with the circuit breakers positioned in two columns operable from the front.

The popular 4-way fusebox normally had two lighting and two socket circuits, with heavy or sustained loads such as immersion heater and oven on a socket circuit. Distribution boards may be surface-mounted or flush. The information includes lighting level information for each channel, by which it controls which dimmer circuits come up and distriubtion out during the lighting changes of the show light cuesand over what fade time.

The former arrangement provides easier alteration or addition to wiring at a later date, but the latter arrangement might be neater, particularly for a residential application.

This arrangement is not recommended practice scherule, but it is common for existing installations. Articles needing additional references from June All articles needing additional references Wikipedia articles with NDL identifiers.

Distribution boards may be designated for three phase or single phase and normal power or emergency power, or designated by use such as distribution panels for supplying other panels, lighting panels for lights, power panels for equipment and receptacles and special uses.

In other projects Wikimedia Commons. Power leaves the board through four three-phase circuits: AC power plugs and sockets Cable tray Electrical conduit Mineral-insulated copper-clad cable Multiway switching Steel wire armoured cable Ring main unit Ring circuit Thermoplastic-sheathed cable.

Electrical wiring Electric power distribution. Some panelboards are provided with a door covering the breaker switch handles, but all are constructed with a dead front ; that is to say the front of the enclosure whether it has a door or not prevents the operator of the circuit breakers from contacting live electrical parts within.

Down the left side of the phase busbars are two two-pole RCBOs and two single-pole breakers, one unused. Instead of just circuit breakers, the rack has a solid state electronic dimmer with its own circuit breaker for each stage circuit.

distibution Fuseholders in these boxes may not provide protection from accidental contact with live terminals. Views Read Edit View history. The cover has been removed from the lower-right neutral bar; the neutral bar on the left side has its cover in place.

Some older boxes are made of brown-black bakelite, sometimes with a wooden base.

Distribution board

The photograph on the left shows a dual panel configuration: Retrieved 16 June The subpanel is fed by two large hot wires and a neutral wire running through the angled conduit near the top of the panels. Larger installations will often use subsidiary distribution boards.

In North Distrihution, it is common to wire large permanently installed equipment line-to-line.

Please help improve this article by adding citations to reliable sources. Larger boxes with more ways will have separate fuses for large loads such as immersion heater, oven and shower. The other problem with recessing a distribution board into a wall is that if the wall is solid, a lot of brick or block might need to be removed—generally for this reason, recessed boards would only be installed on new-build projects when the required space can be built into the wall.

By using this site, you agree to the Terms of Use and Privacy Policy. Panels are located throughout the building in electric closets serving a section of the building. The three incoming phase wires connect to the busbars via a main switch in the centre of the panel. In the United Kingdom, a distribution board designed for domestic installations is known as a consumer unit. Other devices, such as transformers e.

This configuration appears to display three violations of the current U.

Panel Schedule Software | Load Schedule Design | Distribution Board Software

In addition to the achedule feed from the supply transformer in the building, a control cable from the lighting desk carries information to the dimmers in a control protocol such as DMX Most of the time, the panels and the breakers inserted inside them must be by the same manufacturer. For each phase, power is fed along a busbar.

The installations they supply will not meet modern standards for electrical safety.

4 thoughts on “Distribution board schedule

  1. I apologise, but, in my opinion, you are mistaken. I can defend the position. Write to me in PM, we will discuss.

Leave a Reply

Your email address will not be published. Required fields are marked *